Interlock Definition for Switchgear

An interlock is a mechanical or electrical means of enforcing an operating condition. It prevents an action unless defined prerequisites are satisfied, or prevents incompatible actions from occurring together. In new switchgear, an interlock might govern access to a compartment, operation of a switching device, or a sequence involving connected equipment. Its purpose is to make a specified operating relationship part of the equipment design rather than relying only on an operator to remember it.

An interlock is not a substitute for an overall protection and safety strategy. Protective relays, physical barriers, operating procedures, and equipment ratings serve different functions and may work alongside interlocks. The project team should define the hazard or incorrect sequence the interlock is intended to address, then verify the design against the system configuration and applicable requirements. The term alone does not establish a particular mechanism, performance level, or standard listing.

Mechanical and Electrical Approaches

A mechanical interlock uses physical components, such as a linkage, key arrangement, or blocking feature, to restrict an operation based on equipment position or sequence. An electrical interlock uses control-circuit logic or switching devices to permit or inhibit an operation when specified electrical conditions are met. Some designs combine both approaches. The appropriate choice depends on what condition must be enforced, what equipment participates, and how the system is expected to behave during normal operation and abnormal conditions.

Selection should consider the devices’ operating mechanisms, access points, control power, indication, and the consequence of a failed or unavailable interlock component. For example, a design relying on an electrical permissive needs defined inputs and a response to loss of control power; a mechanical arrangement needs compatible hardware and an unambiguous sequence. These are project decisions, not universal features of new switchgear. Qualified electrical professionals should review the design and applicable standards for the specific assembly.

Define the Operating Sequence

Begin by documenting the intended operating states and transitions. Identify which device may operate, which must remain in a particular position, and what condition releases each restriction. Include normal switching, maintenance access, transfer or alternate-source scenarios when they apply, and foreseeable recovery steps after an interrupted operation. A sequence table or clear narrative can expose conflicting assumptions before they are translated into hardware or control logic.

The project inputs should include one-line diagrams, equipment arrangement, device types, control schematics, source relationships, and the owner’s operating philosophy. Confirm which conditions are sensed directly and which are inferred from auxiliary contacts or other signals. Define the required indication and any permitted manual override, including who authorizes it and under what controlled procedure. An interlock should not be specified as a vague request to prevent unsafe operation; its initiating conditions, blocked actions, and release conditions need to be explicit.

Coordinate Equipment Interfaces

Interlocks often cross equipment boundaries. A switchgear assembly may need to coordinate with another lineup, a transformer, a generator, a transfer arrangement, or a site control system. Establish responsibility for each interface: what device supplies a permissive or status signal, how that signal reaches the interlock, and which party defines its meaning. Confirm contact requirements, control voltage, wiring points, signal polarity, communication dependencies, and any required fail-safe response during design review.

Physical interfaces matter as well. A mechanical key sequence depends on compatible locks, key control, equipment arrangement, and an agreed sequence across all participating devices. Electrical schemes depend on documented control-circuit boundaries and suitable interface components. Do not assume a particular interface, control voltage, or communication method is included in a proposed assembly. Record these choices in the project specifications and drawings, then have the relevant equipment suppliers and qualified project professionals reconcile the interfaces before release for manufacture.

Verification, Testing, and Standards

Interlock verification should demonstrate the documented sequence, not merely show that a device operates. Review drawings and logic for each permitted and prohibited action, then define inspection and functional test steps appropriate to the design. Tests should confirm inputs, indications, blocking behavior, reset or recovery behavior, and response to relevant loss-of-signal or control-power conditions. The scope and method depend on the equipment and project; testing must be planned and performed by qualified personnel under applicable safety procedures.

Standards and listing requirements depend on the assembly type, design, and intended use. UL 891 applies to suitable switchboards and should not be assumed to cover every switchgear product or interlock arrangement. Identify applicable requirements with the project’s electrical professionals and relevant authorities. For a new equipment package, request the proposed interlock description, interface drawings, sequence documentation, and verification responsibilities as part of submittal review. Resolve deviations before approval rather than relying on an informal interpretation of the word “interlock.”

Specify the Interlock Before Procurement

When requesting new switchgear, provide the one-line diagram, equipment schedule, operating sequence, and a written list of actions that must be prevented or conditioned. Identify participating devices and equipment furnished by others, along with expected control-power and status interfaces where known. State whether the design should use mechanical means, electrical logic, or a coordinated combination, while allowing the design team to confirm feasibility against the actual configuration and applicable requirements.

Ask for a project-specific explanation of how each condition is enforced, how the operator receives status, and how maintenance or abnormal conditions are handled. Review proposed drawings for signal ownership, device states, key sequences, test points, and exceptions. Confirm the assembly scope, applicable standards, and any UL 891 status only where relevant to the equipment being offered. These details help align a manufacturer’s custom assembly with the owner’s operating intent and identify open decisions before procurement documents are finalized.

Project specification checklist

Use this checklist to organize the details for a project-specific review. Final ratings, applicable standards and equipment selections depend on the approved design.

ItemWhat to confirm
Operating sequenceConfirm permitted actions, prohibited actions, prerequisites, and recovery steps for each relevant operating state.
Interlock methodDetermine whether mechanical, electrical, or combined means suit the defined conditions and equipment arrangement.
Equipment interfacesIdentify participating devices, signal ownership, contact and control requirements, and boundaries with other suppliers.
Indication and overrideSpecify operator status, any authorized override conditions, and the procedure governing exceptions.
Verification scopeAgree on drawing review and functional checks for inputs, blocking behavior, indications, and relevant failure conditions.
Applicable requirementsHave qualified professionals confirm standards and any listing requirements for the specific assembly and project.