What an Automatic Transfer Switch Does

An automatic transfer switch (ATS) monitors designated power sources and changes the connection supplying a load when its control logic identifies a qualifying condition. In a common arrangement, the defined sources are normal utility power and an alternate source such as a generator. The switch transfers the load according to its configured sequence; it does not create power or determine whether either source can support the connected equipment. The specific response depends on the selected ATS, control settings, source conditions, and project requirements.

For equipment selection, the key question is not simply whether a transfer switch is needed, but what sources it must connect and what behavior the load can tolerate. Transfer may be open, with a brief interruption between sources, or another transition method if the design and equipment support it. Confirm the required sequence with qualified electrical professionals, considering the load, source characteristics, and applicable project criteria.

Define the Sources and Load First

Start by documenting each source the ATS is expected to use: its origin, electrical characteristics, normal role, and conditions under which it is considered available. Identify the intended load or downstream distribution equipment, including whether the ATS serves one defined load group or feeds a larger assembly. Source voltage, phase, frequency, grounding arrangement, and neutral treatment are project inputs, not assumptions. The equipment must be selected for the actual system and reviewed against the drawings and specifications.

Also establish which loads are essential, whether they may be interrupted during transfer, and whether they require a particular restoration sequence. Loads with motors, electronic controls, or other sensitivity to voltage interruption may affect transition and timing decisions. Clarify whether load shedding, staged pickup, or other controls are part of the broader system. These choices help define the ATS application, but they should be validated by the engineer responsible for the electrical design.

Selection Criteria Beyond Nominal Voltage

ATS selection requires more than matching a voltage label. The design team should verify the required continuous current, available fault conditions, number of poles, switching arrangement, enclosure environment, and the applicable equipment standards for the proposed assembly. Ratings and construction options vary by product and application; none should be treated as universal capabilities. Confirm compatibility with upstream protective devices, conductors, the alternate source, and the downstream equipment as part of the complete system review.

Control and transition options also matter. Determine how source availability is sensed, what conditions initiate transfer and retransfer, and what delays or manual controls the operating sequence requires. Decide whether the application calls for an open transition or whether a different approach is necessary and supported by the design. These decisions should account for source stability, load behavior, and operating procedures. Standards and listing applicability depend on the equipment and final design, so they must be verified for the specific project.

Coordinate Controls and Interfaces

An ATS participates in a wider electrical system, so its interfaces should be identified early. Coordinate control signals and operating logic with the generator or other alternate source, protective devices, upstream distribution, and any monitoring or building control systems included in the project. Confirm which party provides each signal, what status information is needed, and how abnormal conditions should be indicated. Interface definitions prevent assumptions about control wiring, communication, or responsibilities from being left until equipment integration.

Drawings and specifications should show the source connections, load connection, control power expectations, neutral and grounding approach, and relevant interlocks or operating modes. The design team should also confirm physical and electrical compatibility with adjoining equipment and the intended installation environment. For custom new switchgear assemblies, provide the manufacturer with the current one-line diagram, schedules, control narratives, and interface requirements. A qualified electrical professional should resolve conflicts and approve the final design before release.

Plan Verification and Operating Tests

Testing should demonstrate that the defined sources, sensing logic, controls, and transfer sequence work together as intended. Project documents should state which factory or field verification activities are required, who is responsible, and what acceptance criteria apply. The precise test plan depends on the design, contract requirements, applicable standards, and site procedures; do not infer a particular test or certification from the term ATS alone. Coordinate any testing involving installed electrical systems with qualified personnel and the responsible site representatives.

Before procurement, identify expected operating scenarios, including loss and restoration of the normal source, alternate-source readiness, and any permitted manual operation. Confirm how the system should respond when a source is unavailable or outside acceptable conditions, as defined by the project. Test documentation and control settings should correspond to the approved drawings. No testing plan should require unqualified personnel to work on energized equipment; safety procedures and authority requirements govern site activities.

Prepare a Complete Equipment Request

A useful request for new ATS equipment begins with the one-line diagram, source and load data, required sequence of operation, and project-specific ratings or construction criteria. Include interface schedules, enclosure and installation constraints, applicable standards, and required submittal or testing documentation. State any preferences for transition behavior, control features, or integration, while marking unresolved items for engineering review. This information allows a manufacturer to evaluate the intended assembly rather than guess at system conditions.

For Austin and Central Texas projects, coordinate the equipment schedule with the project’s design, approval, and installation milestones; shipping can be arranged nationwide, but timing depends on the project and confirmed scope. Request a specification review before release to resolve missing inputs, interfaces, and design choices. New custom assemblies can be built to specification in the USA using all-American components; UL 891 applies only where the proposed assembly is suitable for that standard. Confirm all ratings, standards, lead time, and submittal requirements for the actual design.

Project specification checklist

Use this checklist to organize the details for a project-specific review. Final ratings, applicable standards and equipment selections depend on the approved design.

ItemWhat to confirm
Source configurationIdentify each defined source, its system characteristics, and the conditions used to determine availability.
Load requirementsDescribe served loads, interruption tolerance, pickup sequence, and any load-shedding needs.
Electrical and construction criteriaConfirm project-specific current, fault conditions, poles, enclosure, and applicable standards with the design team.
Transfer sequenceSpecify sensing, transfer and retransfer logic, transition approach, delays, and manual operating requirements.
Interfaces and verificationDocument control signals, connected equipment, required tests, responsible parties, and acceptance criteria.