Start with the governing coordination requirement
Selective coordination is intended to limit the effect of a fault to the protective device nearest the fault, while keeping upstream portions of the system energized where the design and operating conditions allow. Requirements are not identical for every project. They may arise from adopted electrical codes, equipment application, owner criteria, utility conditions, or other project documents. The applicable edition, amendments, occupancy or system classification, and authority having jurisdiction must be identified rather than assumed.
For new switchgear, establish which feeders and protective-device chains are subject to selective coordination and what evidence the project requires. Ask the electrical engineer and code authority to resolve scope, exceptions, and documentation expectations before equipment is finalized. A requirement for coordination does not itself establish a particular switchgear rating, device type, or listing; those depend on the system design and applicable standards.
Gather the system data that governs protection
Coordination depends on the complete electrical system, not a switchgear catalog selection alone. Collect the one-line diagram, nominal system voltage, available fault-current information, transformer data, conductor and grounding details, and the protective devices upstream and downstream of the proposed assembly. Include normal and alternate sources, ties, generators, and other operating configurations when they can change current levels or fault paths. Confirm which data are preliminary and which have been verified.
Device manufacturer and model, trip unit or fuse characteristics, adjustable settings, and current-limiting behavior can all affect coordination. Obtain time-current curves and relevant equipment limitations for the actual proposed devices. If values or devices are still unknown, record the open assumptions and assign responsibility for resolving them. Qualified electrical professionals should evaluate the data and confirm that protection choices also address applicable fault-clearing and equipment withstand requirements.
Map device interfaces and operating scenarios
A useful coordination review traces each required path from a downstream branch or feeder device through distribution equipment to the source-side protective device. Mark the boundaries of the new switchgear assembly and identify interfaces with existing gear, utility protection, transformers, transfer equipment, emergency sources, and downstream panels. Selective coordination can be affected by devices outside the supplied assembly, so responsibility for obtaining their settings and curves should be clear.
Review credible operating modes separately. A tie normally open may be closed for maintenance or contingency operation; a generator or alternate source may produce a different fault contribution than the normal source. The engineer should identify which configurations must satisfy the project criteria and whether settings or interlocks change between modes. Documenting these scenarios early helps prevent a design that coordinates on one assumed one-line arrangement but fails to address another required operating condition.
Evaluate devices, settings, and design tradeoffs
The coordination study should compare protective-device time-current characteristics for the relevant fault-current range and system configurations. It should account for device tolerances, adjustable trip functions, fuse characteristics where used, and the equipment manufacturers’ stated limits. A visual curve comparison is one tool, not a substitute for checking the project’s defined coordination criteria and the performance of the complete protection scheme.
Design decisions may involve device family, trip-unit functions, setting ranges, feeder arrangement, and coordination with upstream protection. A change intended to improve selectivity can affect clearing time, arc-flash evaluation, equipment protection, or available fault-current limits. These objectives can compete; no setting should be selected in isolation. The responsible engineer should resolve conflicts, document approved settings, and verify that proposed new switchgear and associated devices suit the project conditions. UL 891 applies only to suitable switchboard assemblies, not automatically to every switchgear application.
Verify the design and control changes
Before release, align the one-line diagram, equipment schedules, device submittals, coordination study, and setting schedule. Check that each protective device shown in the analysis matches the proposed equipment by manufacturer, type, sensor or rating basis, and trip functions. Review assumptions about source fault current, conductor lengths, transformer impedance, and operating modes. A discrepancy can make otherwise careful coordination results inapplicable to the delivered configuration.
Coordination is commonly verified through engineering analysis of device characteristics and system data; the project documents should define any required review, witness, or field verification. Do not treat a generic factory test as proof that the installed system meets selective coordination criteria. Establish how final settings will be communicated, recorded, and checked by qualified personnel. Revisions to sources, feeder routing, devices, or settings should trigger review of affected studies and documents, with work performed under appropriate safety procedures.
Prepare a procurement package that can be checked
For a new switchgear quotation or submittal, provide the current one-line, equipment scope, system data, specified coordination criteria, required operating modes, and known upstream and downstream device information. Identify who will furnish missing curves, perform or approve the study, and issue final settings. State required submittal content and review milestones so the equipment design can be evaluated before fabrication. If specifications are unsettled, list questions for the engineer and authority rather than embedding unverified assumptions in the purchase documents.
A US manufacturer can develop custom assemblies to project specifications, with applicable construction details and standards confirmed during review; UL 891 should be specified only where the assembly and application qualify. For Central Texas projects or shipments elsewhere, coordinate document review, delivery sequencing, and site receiving constraints with the project team; location does not establish local service or a particular lead time. The practical next step is to submit the one-line and device schedule, identify unresolved sources or settings, and request a written scope and submittal plan for engineering review.
Project specification checklist
Use this checklist to organize the details for a project-specific review. Final ratings, applicable standards and equipment selections depend on the approved design.
| Item | What to confirm |
|---|---|
| Applicable requirement | Confirm adopted code edition, amendments, project criteria, affected circuits, exceptions, and authority review. |
| System and fault data | Verify source configurations, available fault current, transformer information, grounding, and feeder details. |
| Protective-device records | Identify actual device models, trip functions, settings or ranges, curves, and equipment limitations. |
| Coordination boundaries | Map upstream and downstream interfaces, alternate sources, ties, and required operating modes. |
| Study and acceptance | Define analysis scope, review responsibility, required documents, final setting records, and change control. |